Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Dorman 924 - 251 Cadillac/Chevrolet/GMC líquido limpiaparabrisas manguera

Envío gratis en pedidos superiores a Mex $600.00

Mex $686.44

Mex $ 308 .00 Mex $308.00

En stock

Acerca de este artículo

  • Un artículo de seguridad necesario para mantener el sistema de limpiaparabrisas en condiciones de funcionamiento adecuadas
  • Reemplazo directo para un ajuste adecuado cada vez
  • Fácil de instalar
  • Se han tomado rigurosas medidas de control de calidad para garantizar que esta pieza cumpla con las normas del producto
  • Asegúrate de que esta pieza se ajusta a tu vehículo exacto, introduce tu marca, modelo y nivel de corte en el cochera de Amazon


Dorman mejorado para abordar los puntos de fallo en el material original, nuestras mangueras de limpiaparabrisas están fabricadas con un plástico de grado más fuerte para una mayor durabilidad. Esto fortalece la manguera contra daños, evitando agujeros y ayudando a garantizar que el líquido de la lavadora llegue al parabrisas sin impedimentos.


andrew
Comentado en los Estados Unidos el 6 de agosto de 2024
Received this for my 03 Silverado 1500. Installed with no issues. Keep in mind this only goes from the washer tank to the fuse box area. If you want the section that runs the rest of the way you will have to buy separately. Otherwise, no issues.
Steven Thompson
Comentado en los Estados Unidos el 14 de julio de 2024
fits perfect on 2004 silverado. easy install
David Petros
Comentado en los Estados Unidos el 4 de abril de 2021
This front washer hose fits many years Chevrolet Silverado - mine is a 2002. It runs from the washer reservoir to a connection just past the battery on the fender. Because it comes bent up to fit inside a standard box for shipping, you will need to adjust the over-bends. They need to be straightened a little to approximately 90 degree bends. This can be verified by looking at the old part before it is removed. Some people have mentioned using hot water or a heat gun to soften the bends. For simplicity, I used a candle in a glass jar. I held the over-bent sections about two inches above the flame and moved the part back and forth and rotated it as much as I could until it started to loosen each bend. I stopped when the bends were at approximately 90 degrees.Check online for advice on the labor to replace the part. I had dropped the part into place for rough alignment. I discovered that I was able to reach the elbow hose connection at the reservoir pump from under the truck by reaching up behind the bumper. I used a fork-shaped panel removal tool to pry the hose off, although a screwdriver may have also worked. My arm got soaked as the washer fluid started pouring out, but I was prepared for that and I pressed on the new elbow quickly. I may not have actually needed to remove the battery for this job, but I had taken it out already.Other purchasers have noted that the part did not last long for them. I just installed mine today. I will updated my review if I have any problems.Update 5/6/22: Since installing this hose last year, I have had trouble with it a few times. The rubber tip on this hose does not have a strong grip on the washer tank pump. It sometimes holds for a short spritz of washer fluid on the WS, but will likely pop off with a prolonged blast and leak all the fluid onto the ground. I’m thinking of tightening it with a small zip tie.3/18/24: Small zip ties on both ends of the hose worked for almost a year as the truck sat parked most of the time. When I needed the washer, the hose popped off the reservoir pump and will not reliably stay attached. Can’t find an AC Delco brand, so I will reorder this hose in hopes that they have improved the design since 2021.
Miss K
Comentado en Canadá el 7 de marzo de 2020
Perfect fit. Works great. Quick shipping.
Barrie
Comentado en Canadá el 9 de abril de 2018
Exactly as advertised. Windshield washer works great again.
Productos recomendados