No hay artículos en el carro
No hay artículos en el carroPaquete: 5 fresas cuadradas HRC55 de 6 mm
Anvarbek
Comentado en los Estados Unidos el 16 de marzo de 2025
Best of the best a lot of room to work with
Joseph dipietro
Comentado en los Estados Unidos el 11 de marzo de 2025
No se pudo cargar el contenido.
Pedro Fuentes
Comentado en los Estados Unidos el 25 de enero de 2025
My son loves this case.
Brandon Steele
Comentado en los Estados Unidos el 15 de abril de 2025
great case. lots of room to work in. it's so nice and purdy. filters are easy to mess with. only down side is I can't find any fans that match the pre installed for the bottom, but that's a me problem. if I ever build another white PC I'll probably be getting this again.
Joso
Comentado en los Estados Unidos el 8 de abril de 2025
This case is good overall, but the fans are inexpensive and suffer from flickering RGB lighting. There's no dedicated software available to manage their speed or lighting effects, so users must rely on the LED button located on the side. Additionally, the vertical GPU mount sags noticeably from both the front and side views.
NST005
Comentado en los Estados Unidos el 6 de agosto de 2024
These are not 1/4 as advertised, nowhere near it. These do not fit 1/4 collets and I tested these on 3 different routers
Jasmine Z
Comentado en los Estados Unidos el 21 de enero de 2024
No se pudo cargar el contenido.
JThayer
Comentado en los Estados Unidos el 2 de enero de 2024
15/64" is, for me, an odd size for an endmill. But, having the opportunity to test these out, I decided to give them a shot. But first, do I have a way of holding this size shank? Turns out that my 1/4" collet had no problem clamping down to 15/64" and held these endmills just fine. Tested with mild steel as that is what I am usually working with. They cut smooth left behind a reasonable surface finish. The Amazon page didn't (at least that I saw) say whether they were center cutting, but I had no problem plunge milling with them. Bottom-line: they work well.
Matthew Paradis
Comentado en los Estados Unidos el 29 de diciembre de 2023
First, this review is from the perspective of a hobby machining person using a relatively small (350 lbs) vertical milling machine. I mill steel, aluminum, and occasionally titanium. These end mills work very well for me, IF used for the correct material and feed/rpm. I have ruined enough end mills to know that usually it’s my fault when a bit gets ruined. Four flutes cut fast and clean but in Titanium that’s not always ideal, since chip clearance rate can be an issue (if you recut titanium chips it gets gummy and binds to the end mill, ruining it). So these mills are well ground, sharp, and cut well in steel and things like micarta. If you have a problem with these mills it’s probably you using it on the wrong material, in the wrong way. If you run a machine shop where you are trying to feed at the highest rate possible to maximize efficiency, maybe inexpensive mills aren’t where you should be looking. For the hobbyist, doing occasional projects, these are perfect. I would get them again.
Productos recomendados
Mex $245.00
Mex $ 134 .00 Mex $134.00
Mex $918.72
Mex $ 496 .00 Mex $496.00
Mex $249.00
Mex $ 129 .00 Mex $129.00
Mex $275.00
Mex $ 137 .00 Mex $137.00
Mex $778.00
Mex $ 427 .00 Mex $427.00
Mex $320.00
Mex $ 153 .00 Mex $153.00