No hay artículos en el carro
No hay artículos en el carroDisco Sierra Corte de Metales Ferrosos de Calibre Grueso Diámetro 14 pulgadas Dientes 66 Puntas Carburo Flecha 1 pulgada Ángulo del Gancho 1.5 Corte 0.091 Molienda del Disco M-ATB Velocidad Máxima 1800 RPM
Guillermina
Comentado en México el 15 de febrero de 2022
Muy buena en cortes transversales, en perfiles de 4" en corte 45° patina y se calientan demasiado los dientes, optó por terminar el corte con disco abrasivo y si titubeas un poco al cortar corre el riego de romperse los dientes.Además es demasiado cara.
Jose Cetina
Comentado en México el 31 de enero de 2021
Todo muy bien. Cumplió mis expectativas en calidad precio y tiempo de entrega
Julia
Comentado en Canadá el 15 de julio de 2020
Good product. Cuts steel in chop saw
Cliente de
Comentado en México el 3 de diciembre de 2018
Necesito hacer más cortes para dar mi opinión. A ver si da los 1500 cortes que dice poder hacer antes de tener que reemplazarlo. Lo que no dice es el promedio del grosor de los cortes y la velocidad de corte antes de considerar que necesita remplazo.
Harold S.
Comentado en Canadá el 18 de noviembre de 2017
Item almost as listed, not 70 tooth but, 66 tooth. I'm happy though, probably an error on there part. Good price.
schnick
Comentado en los Estados Unidos el 28 de noviembre de 2014
I have a small fab shop and we use this daily for cutting everything from 1" square steel tube .100 wall all the way up to 5"x 3" .250 wall steel tube, 1/8",3/16",1/4"and 3/8" x up to 4" angle as well as aluminum extrusions 1",2",3" square aluminum tube (a little wd40 on the blade while cutting aluminum helps keep the teeth clear) and I usually get a couple of months out of the blade before it needs sharpening, I've gotten the same blade sharpened a few times before it needed retirement, usually due to lost teeth. I have four of these blades and cycle them, when they get dull I switch it out and send it out for sharpening.I haven't kept count of how many cuts we're getting but I would guess at least a thousand as long as the material is clamped properly and supported when cutting long pieces, if the work piece moves while you're cutting it will remove teeth in a hurry ruining the blade.I've got an abrasive blade chop saw and it hasn't been used in years other than to cut hardened shaft like thomson or superior shaft since I bought the Dewalt dw872 that uses this blade, it makes cuts cleaner, faster and more square than the abrasive blade ever could, without all the dust!Also a word of caution you can't use this blade on an abrasive blade machine because the wheel speed is too high, and don't use it on hardened shaft or you'll get a very short life out if it speaking from expensive experience.
schnick
Comentado en Canadá el 28 de noviembre de 2014
I have a small fab shop and we use this daily for cutting everything from 1" square steel tube .100 wall all the way up to 5"x 3" .250 wall steel tube, 1/8",3/16",1/4"and 3/8" x up to 4" angle as well as aluminum extrusions 1",2",3" square aluminum tube (a little wd40 on the blade while cutting aluminum helps keep the teeth clear) and I usually get a couple of months out of the blade before it needs sharpening, I've gotten the same blade sharpened a few times before it needed retirement, usually due to lost teeth. I have four of these blades and cycle them, when they get dull I switch it out and send it out for sharpening.I haven't kept count of how many cuts we're getting but I would guess at least a thousand as long as the material is clamped properly and supported when cutting long pieces, if the work piece moves while you're cutting it will remove teeth in a hurry ruining the blade.I've got an abrasive blade chop saw and it hasn't been used in years other than to cut hardened shaft like thomson or superior shaft since I bought the Dewalt dw872 that uses this blade, it makes cuts cleaner, faster and more square than the abrasive blade ever could, without all the dust!Also a word of caution you can't use this blade on an abrasive blade machine because the wheel speed is too high, and don't use it on hardened shaft or you'll get a very short life out if it speaking from expensive experience.
Joseph M.
Comentado en los Estados Unidos el 30 de diciembre de 2013
DO NOT INSTALL THIS BLADE IN A PORTER CABLE MACHINE. It will turn too fast and you will be one of the morons complaining about the short life of the Dewalt blade. I bought this as a backup for the DW872 saw from Dewalt. Remember that it has to turn much slower than most all abrasive saws turn, and turning it faster will just shorten its life, and possibly your own. This means that turning the bladed faster than 1300 RPM can be very dangerous, and the danger is all in relation to how much faster you turn it, and what you cut with it. Even the saw it is made for, which runs at the correct speed, must be used properly to prevent damage to the blade, to the work, and to the user. Never rush the cut, the slower you go, the less heat and damage to the blade you will get. I cut angle iron, like bed frame material with ease. It cuts aluminum fast an easy. Always run the blade no faster than the specifications say to run it. The least you will do is ruin the blade, the most you will do is ruin your life.
Productos recomendados
Mex $359.41
Mex $ 190 .00 Mex $190.00
Mex $513.84
Mex $ 277 .00 Mex $277.00
Mex $449.00
Mex $ 220 .00 Mex $220.00
Mex $581.48
Mex $ 261 .00 Mex $261.00