Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

GearWrench 2031DD Exhaust and Tailpipe Cutter

Envío gratis en pedidos superiores a Mex $600.00

Mex $931.99

Mex $ 447 .00 Mex $447.00

En stock
  • Use tool to cut pipes 3/4-Inch to 3-Inch in diameter
  • Fifteen blades effectively cut pipe so only a quarter turn is needed for complete cut
  • Tool works well in hard to reach areas



Más información del producto

GEARWRENCH Cortador de tubo de escape y escape

GEARWRENCH Cortador de tubo de escape y escape

Características:

Corta tubos de 19 mm a 76 mm de diámetro. Quince cuchillas cortan eficazmente el tubo por lo que solo se necesita 1/4 de vuelta para un corte completo. La herramienta de servicio funciona en zonas difíciles de alcanzar. No corta tuberías de doble pared. Mantener bien engrasado. No es para uso en acero inoxidable


Abdullah Bekir Özbek
Comentado en Turquía el 23 de enero de 2024
Ürün güzel ve kesici bıçakları kaliteli ama uzun süren bir çevirme işlemi yaparak kesmeniz gerekiyor eğer sabırsız biriyseniz işiniz dahada zorlaşıyor
Jose Antonio Diaz Palacios
Comentado en México el 8 de junio de 2023
Solo corta tubo de pared muy delgada
mario alejandro rodriguez gallardo
Comentado en México el 26 de marzo de 2023
Cumple con asbexpectativas de su uso. Me gusto rapida y cilensiosa
Brendan Vandersteen
Comentado en Canadá el 25 de septiembre de 2022
Works well. Use lots of oil. BEWARE… DO NOT use too much force when using this cutter. Many people claim this tool breaks almost instantaneously when using… Those individuals need to RELAX their iron grip… You must start the cut fairly gently and continuously add pressure and wiggle the wrench back and forth while cutting the pipe. When you are mostly through the pipe, then add lots of grip strength and you will end up with a clean cut. On my first attempt I used a bit too much strength and ended up with a slightly jagged cut, I was able to bend the pipe back to normal — I suspect that most people who are breaking this tool are using TOO MUCH power right at first resulting in either a bent pipe or bent/broken blades. Use your noggin, not your testosterone on this one.. This tool allows for nice clean cuts with a bit of patience.
Henri Robinson
Comentado en el Reino Unido el 10 de septiembre de 2020
Did the job perfect, thank you
Michael Scarn
Comentado en los Estados Unidos el 9 de diciembre de 2015
A really clever design for a pipe cutter; the blades are sharp and it cut a nice track. You do have to be patient with cutting steel pipes, and take care initially to lay out a good track... lots of patience is required with thicker hard stainless steel pipes, but when you finally get done it make you feel like a real man! It's technically is not meant for stainless steel, but concensus here is that should probably work, except dull the blade and so it would be a one time or two time use tool which is fine at that price. After cutting midway I sprayed wd40 as cutting oil; silicone spray or marvel mystery oil would have been much better lubricant. Near the end of the cut when part of the pipe is cut through and other parts are not, it gets rougher and friction in the sawing oscillations; once the metal is thin enough you might just want to try twisting the pipe. It's also handy at that point to have a small hacksaw with fine teeth at your side.
Abdul Hassan
A must-have tool if you wish to cut off your catalytic converters by yourself and clamp-on a new one!
Productos recomendados

Mex $2,125.13

Mex $ 892 .00 Mex $892.00

5.0
Elegir

Mex $503.51

Mex $ 246 .00 Mex $246.00

4.3
Elegir