No hay artículos en el carro
No hay artículos en el carro
Material: aleación de aluminio (100% nueva).
Color: dorado y plateado.
Tamaño del panel: 240 x 200 x 5 mm.
Distancia del orificio del tornillo: 70 x 62 mm (2.76 x 2.44 pulgadas) / 56 x 45 mm (2.2 x 1.77 pulgadas)
Paquete:
1 placa de inserción de mesa de enrutador.
1 valla de enrutador.
1 medidor de inglete.
2 anillos de goma.
Nota:
Este producto no incluye la máquina. Nuestro lente es crear una experiencia de compra cómoda para los clientes. Si no estás satisfecho con nuestros productos, puedes ponerte en contacto con nosotros en cualquier momento, y te proporcionaremos servicios cálidos.
Maynard
Comentado en los Estados Unidos el 3 de mayo de 2025
Haven't mounted this yet but seems to be of good quality
Douglas Komack
Comentado en los Estados Unidos el 18 de abril de 2025
Cheaply made and impractical , No way to fit to my router . Fence and miter gauge sloppyI had to return it.
Repair Man
Comentado en los Estados Unidos el 4 de junio de 2024
These are high quality and significantly less expensive than other manufacturers. I bought the pair for my existing 127mm and new 72mm telescopes so I could switch filters between. For those inexperienced like myself, the light pollution and narrowband filters are unidirectional and the filter drawer is unidirectional. What this means is the 48mm female thread must attach to the telescope and the 42mm male end (comes with 42mm to 48mm male adapter) must attach to camera/eyepiece. Use this info to purchase the correct adapters. For your particular scope
dale armstrong
Comentado en los Estados Unidos el 23 de junio de 2024
It’s pretty small an the quality is good,it’s good for small jobs like I do, it will do for me, but if you do a lot of work I would get a bigger one. The holes would not match up to big dewalt router had to get a smaller router an then they matched perfect.
Lewis Balentine
Comentado en los Estados Unidos el 15 de mayo de 2024
This is one of a number of router inserts on Amazon designed to be used with a router lift for a 65 mm diameter trim router. I bought this along with a matching two-post router lift. I have no complaints regards the router lift.My main complaint about this insert plate is that the diameters of the hole and the counter bore for the a template bushing are over-sized and not concentric. They are also not centered on the center of the router bit when the lift and router are mounted to the plate. In my narrow minded opinion this makes it impractical to use a template bushing with this insert plate.This insert plate and lift are designed to be used with the “hand crank” for the router lift located approximately 1.7 inches (50 mm) to the rear of the center of the router. The fence covers the hole for the router lift crank. I will refrain from making further comment on this aspect.There are two screws used to mount each section of the fence. They are both M6 fasteners and use the same style square nut inside the channel of the extruded fence section. However one has a hex socket head head and the other has a #2 Phillips (aka ‘cross’) countersunk head. A minor problem that could be solved by replacing the latter with proper M6 x 12.5 mm long hex socket head head fasteners. The two scales (0 to 9 cm) have no meaningful relationship to anything on the insert plate except each other. Lastly I do care for the 10 mm x 3 mm miter slot or its accompanying cheap miter gauge.The “big surprise” was that the hole pattern used to mount the router lift is NOT symmetrical front to back. To be fair, it is symmetrical left to right.The only reason I am giving this insert plate two stars is because it did attach to and fit the router lift perfectly.I had a heck of a time making a dimensioned drawing for this part and found some surprises along the way. I am a half blind, senile old man. The dimensions shown in the drawing are as close as I could measure them. If I was going to use this part then I redo the drawing to normalize the dimensions to the nearest half millimeter. However I do not consider this part worth wasting any more of my time on. I have purchased a different 120 mm square insert to replace it.
Night Sky Fan
Comentado en los Estados Unidos el 2 de diciembre de 2024
I was surprised at the heft of this filter holder, it weighs more than the large holder from Player One and it is thicker than some competing brands. That noted the design and build are excellent. I detected no light leeaks.The holder comes in a fitted foam hinged plastic case and includes an Allen wrench abd adapters for 1.25 inch filters.The camera side has male M42 threads, and an M42 to M48 adpater is included which makes this holder useful with both my IMX571 camera and the smaller IMX 585 adn IMX249 cameras that I have.
Jim Harris
Comentado en los Estados Unidos el 19 de diciembre de 2024
Out of the box put the unit together and come to fill out some screws were to long and some of the drill hole were to rough for the unit work properly. I was able to fix these issues not sure all could. ,s
Productos recomendados
Mex $1,091.09
Mex $ 512 .00 Mex $512.00