No hay artículos en el carro
No hay artículos en el carro
• Kuali Shoes Empresa Mexicana, nuestros productos están hechos 100% en México. •
jesse allen
Comentado en Canadá el 2 de enero de 2025
got for a ender 3 v2 and worked great plug and play
Mangal14
Comentado en los Estados Unidos el 10 de octubre de 2024
Installed on an Ender 5 pro after the Bltouch smashed into a print and bent its probe pin. The creality cr touch installed easily and plugged into the 4.2.7 board with no issues. re calibrated using klipper and everything seems to be working well with regards to probe distance and auto bed leveling.I wish the ender 5 X gantry bracket was designed better to hold the hotend and cr touch. It is not easy to screw in the M4 screws that hold everything in place, especially the one behind the cr touch.
Sean Tomlinson
Comentado en los Estados Unidos el 21 de abril de 2024
The CR touch works fine (albeit with my limited use so far), but this isn't reason enough to give this productb5 stars imo. The technology isn't new, creality didn't invent it (I do appreciate the probe being in metal instead of plastic like the BL touch, because... heated bed...).But the reason I'm giving thisb5 stars is Creality's decision to include several well thought out mounting brackets in the kit... Don't roll your eyes and stop reading yet... listen to my experience.I used this product on an Ender 3 V2 at the same time that I purchased a X Axis linear rail kit (also from Creality). I did not; however, order the V2 mounting plate. I ordered the Creality Sprite extruder plate (even though I don't own this extruder yet, I just wanted to keep that option open for the future (I really like that extruder it will be mine one day). None of this is noteworthy so far, everything mounted fine with the V2 bracket included.But then I decided that I needed a 2nd print cooling fan and instead of designing one myself... Thingyverse... maybe you can see where this is going. After sone creative thinking I got the new shroud together with 2 new fans (3 actually) and tried to mount it... printhead is now to large *wide... paused and pondered, a small tie strap and a screw later mounted... too low, below the nozzle, reconfigured, mounted fine.. right CR Touch hole is gone and bracket width will not allow room for mounting (the touch).Mounting tape as temporary measure til I can print a new bracket... hits X axis limit switch.Then U look in the box and there are 2 brackets that will likely work. 1 would require taking off the printhead and another will work fine and will actually work not only as intended but upside down (because for some reason the probe is now too high). Both in metal at that. Good job Creality, 5 Stars, highly recommended.
FromCanada
Comentado en Canadá el 4 de octubre de 2023
I started having a few problems with bad prints and I couldn't figure out if it was due to bad filament or the bed not being level. The center of the bed was also slightly lower than the corners. I tried fixing that with a couple of sticky notes under the glass and it helped, but I still hated having to manually level the bed whenever I ran into any problems. This has saved me so much time, and uncertainty about what could be causing the problem. I was also able to get rid of the sticky notes since this compensates for any unevenness across the entire bed. I highly recommend this upgrade. Be sure to check out some of the YouTube videos that walk you through the entire installation process because they have some good tips.
Alexander Danis
Comentado en Canadá el 3 de octubre de 2023
The CR-Touch is a MUST have if you don’t currently have one. It’s extremely simple to install and is a game changer! My prints would always fail until I installed this!I would extremely recommend this if you own a 3D printer and don’t have this installed yet!10/10
Ricardo Vázquez
Comentado en México el 6 de enero de 2023
El producto está perfecto más sin embargo me desepciono demasiado que no me llegará el kit de boquillas que menciona que viene incluido, en cuestión de lo demás está perfecto el producto
hector guerrero
Comentado en México el 15 de mayo de 2022
No se si pase a otros pero el firmware bajado de creality hizo ilegible la pantalla y muchos problemas para leer las tarjetas de memoria. Mi equipo es una ender 3 pro con tarjeta madre v422 el sensor funciona pero la interface entre humano e impresora deja we funcionar. ahora estoy en si un cambio de tarjeta madre a la v27 resuelve los problemas o mejor tiro la impresora.
Productos recomendados
Mex $789.00
Mex $ 410 .00 Mex $410.00