No hay artículos en el carro
No hay artículos en el carro
Especificaciones:
Tamaño: 6,6 x 4,06 x 0,16 cm.
Voltaje: 3,3 V.
El paquete incluye:
1 módulo de placa de ruptura para Teensy 4.1.
4 cabezales de pines (24 pines).
4 bloques de terminales (12 pines).
Most badassiest consumer
Comentado en los Estados Unidos el 9 de marzo de 2024
The teensy in the photos is plugged in backwards! VIN is supposed to be next to the USB, not the SD card. When I plugged it in the way shown in this photo, my Teensy stopped blinking, and now it does not even communicate with my laptop at all, even without the breakout board connected. It turns out this is likely due to a design choice. The GND pins are tied together on the breakout board. This normally would be fine if the board is plugged in the right direction. But if you ever plug it in backwards and power it up, several of your GPIO pins will be shorted together, which as I have unfortunately shown, WILL DESTROY the teensy. Had they left all 40 pins isolated on the PCB, this would not have happened, and this danger would have been eliminated. I wish there were a way Treedix were able to replace my Arduino, because I was following their photo for how to plug it in.
Franciso Olguin
Comentado en los Estados Unidos el 26 de enero de 2024
Had to solder it together but expected that, had to solder the pins on the teensy so did both in 1 shot.
Hal Albach
Comentado en los Estados Unidos el 13 de marzo de 2023
A previous review complained about the vendor not supplying the "Little Red Jumpers" as illustrated in the product page. That picture is somewhat misleading because where they show the jumpers there is a trace running between the two involved pads, all 48 pairs. The traces are a little difficult to see because of the black coating. Tilt the board a little under a light and they are easily seen. A quick check with a multimeter will also verify all 48 pairs are connected.As for the "tiny" screws on the green strips, just about any jewelers screwdriver set will have the 3/64" tip.
Tired of all the whining
Comentado en los Estados Unidos el 16 de noviembre de 2023
Got it and had my new Teensy 4.1 mounted in about 15 minutes. It does take some soldering, of course but the pads solder easily. Disregard the comments about needing little red wires!! I think that photo is just showing that those pins are connected together. Each of the Teensy pin mounting points are directly connected to pin mounting points for the solder on screw terminals through runs on the board. No need for anything that's not in the kit - other than a Teensy, of course. As far as comments about the size of the terminal screws - yes, they are small, by necessity I'm sure. I have a jeweler's screwdriver set and and there are at least two screwdriver tips in it that fit the screw slots. If you don't have a set, get one!!
David Miller
Comentado en los Estados Unidos el 7 de abril de 2022
So it's just in parts, huge shocker there wish I'd have read the page, everything is scummy like this now...So what about the jumping the soldered pins in, it shows this bs diagram w. red wire jumper from one to the other (row) but I certainly don't see any? I'm supposed to trail solder across 2mm ? and not hit other pins in the row? this is stupid as it gets..the height for the normal pinheader row is far different too, so if you smartly decide to flip it upside down on a flat surface so you can do this... yep the rows are a different height and the pins are only halfway through so your solder will go all the way through or else you manually have to juggle to hold the pin header in (perfectly or the device will never fit in it... )Safe to say, when it doesn't work out i'm going to be returning a soldered mess back to them
Productos recomendados
Mex $5,454.90
Mex $ 1,881 .00 Mex $1,881.00
Mex $310.20
Mex $ 145 .00 Mex $145.00
Mex $200.00
Mex $ 110 .00 Mex $110.00
Mex $388.50
Mex $ 202 .00 Mex $202.00
Mex $250.00
Mex $ 147 .00 Mex $147.00