No hay artículos en el carro
No hay artículos en el carro Súper compatibilidad.
Repuesto compatible con la gama completa de modelos Roomba 500, 600, 700, 800 y 900.
Características
- Antideslizante, la rueda no se desliza.
- Hecho de materiales 100% de calidad.
- Fácil de montar.
rhode_island28
Comentado en los Estados Unidos el 27 de febrero de 2025
Even though removing my roomba tires wasn’t as easy as I thought, the replacement tires were simple to install, sturdy and perform without slipping. I will repurchase in the future!
carl seymour
Comentado en los Estados Unidos el 27 de enero de 2025
They fit perfectly. Turned my vac into a little tank. They grip so well the vac moved furniture.
M. ASHTON-MOORE
Comentado en los Estados Unidos el 17 de enero de 2025
After trying another brand of replacement tires for my S9 I tried these.The other brand would not maintain grip on carpet and could barely complete a job.Once I cut the old ones off and tried these it returned my S9 to completing jobs again, much better.
Kindle Customer
Comentado en los Estados Unidos el 15 de diciembre de 2024
No detail instructions were included.
Ricardo Cervantes
Comentado en México el 8 de julio de 2023
Recibí un día antes de lo esperado el producto, se ven de buena calidad están funcionando adecuadamente
Iliana C.
Comentado en México el 18 de diciembre de 2023
Muy buen producto a muy buen precio
Francisco Ortiz
Comentado en México el 27 de noviembre de 2023
Duraderas, similares o iguales a las originales.
S. Lonon
Comentado en los Estados Unidos el 11 de noviembre de 2022
I picked these up for $10 rather than going through iRobot as they make you replace both wheel modules.Installation was simple.1: Unscrew bottom plate by removing 5 screws (See picture)2: Identify the wheel modules, and the two gold screws attaching each.I could see this being a difficult step if you do not have the right equipment, as the phillips heads were small.3: Remove the four gold screws. Modules should lift without resistance.I was able to remove the modules without completely removing the screws that were in the deeper holes.4: Use something (I used needle nose pliers, but I imagine a flathead screwdriver might have been easier) to remove the old tires.I pulled from the lip, and then once I was able to get my pliers underneath the rubber, I slowly worked the tires off. I let my roomba run before I did this job, and because the rubber was still warm, I think it was easier than it would be if they were cold. You will probably end up pulling them off in pieces because the OEM tires are anchored in the plastic wheel. Its ok if bits of rubber get stuck in the insertion points. That will only act as additional friction for the new tires to grip.5: Attach the new tires.This was the easiest and most satisfying part of the job for me. I attached the tires by getting half of the tire on the top, then turning the wheel so the seated portion was on the bottom, then worked the other half on. Make sure the interior rib of the new tire sits properly in the channel of the wheel.6: Reassemble.I used a Phillips #2 for the exterior screws, and a Phillips #1 for the interior screws.This was absolutely worth the money. Gone are the days of my roomba not being able to get on the dock properly, or just turning wheels at a threshold. I gave 5 stars but I would give 10 if Amazon allowed it.
Productos recomendados
Mex $216.78
Mex $ 119 .00 Mex $119.00
Mex $3,524.07
Mex $ 1,726 .00 Mex $1,726.00
Mex $603.49
Mex $ 307 .00 Mex $307.00
Mex $478.87
Mex $ 258 .00 Mex $258.00