No hay artículos en el carro
No hay artículos en el carroLas ruedas de banco y pedestal de óxido de aluminio blanco Norton proporcionan la máxima tasa de corte y acción de corte fresco en aceros para herramientas endurecidos o de alta velocidad y otros metales. Las ruedas de banco y pedestal se utilizan para desbarbar y afilar piezas y herramientas. Bujes de eje de 1/2", 5/8", 3/4", 7/8". Especificaciones: Fine 100. Todas las ruedas de banco y pedestal deben vestirse para evitar la carga. La carga puede causar calor excesivo, daños a la pieza de trabajo y rotura de la rueda. El apósito expone nuevos bordes de corte y proporciona espacio última intervensión de astillas. No moler madera, plástico o cualquier otro material no metálico en un banco o molinillo de pedestal. Las máquinas no seguras pueden moverse, causando roturas y lesiones. Las amoladoras de banco y pedestal de base fija deben estar aseguradas.
robert louis
Comentado en Canadá el 11 de noviembre de 2024
This stone runs smooth out of the package. Like all new stones it still needs minor dressing.
Vicars Hodge
Comentado en Canadá el 23 de abril de 2024
As expected of Norton products, this is well made and as described.
terry
Comentado en Canadá el 18 de junio de 2022
The white grinding compound for high speed steel does not get the tool as hot as regular grey carborundum does. This wheel works as it should. I am giving it one star because I had to bolt the grinder to the bench as it vibrates so bad way worse than the cheap wheels that came with the grinder.
George Frederick
Comentado en Canadá el 5 de octubre de 2021
Does what it is supposed to do.
Customer
Comentado en México el 15 de febrero de 2020
Cumple perfecto, entrega antes de lo esperada.
John M.
Comentado en los Estados Unidos el 5 de diciembre de 2014
After reading all the bad reviews I searched for an answer and truly believe I found it! Craft Supplies USA sells what they call the Raptor R3X Grinding Wheel Bushing 2 Piece Set. This is a wonderfully made flange with an attached bushing that you can order to either fit a 1/2" or 5/8" motor shaft. It comes as two pieces, the flange with the busing is all one piece, and then there is another flange for the other side (I did not use this, but rather used the original inner flanges for the grinder). The bushing is 3/4" long, but will work on a 1" wide wheel without problem (the wheel I ordered is 6x1x1). I ordered two of these sets as the past owner of my 1920's grinder had ended up using just big washers as flanges on the outside of the wheels. I ordered the sets and then ordered the Norton wheel, so I was ready to go when the wheel arrived. I couldn't be more pleased!!!! I didn't waste time with the plastic bushings that were supplied as everyone seems to agree they are not the best. I pulled them out and stuck my new Raptor bushing flange in and put it on the grinder. NO WOBBLE as so many had described, and it was so perfectly in round that I doubt there is even 1/32" variance to be dressed (yes, I think it is less than that...maybe 1/64"). WOW! Very pleased! As far as shipping goes, I ordered the wheel alone so it would be all that was in the box from Amazon and not be bumping into other things. It was sent in a box similar to what Amazon sends books in, so there was no wiggle room in the box. It arrived in perfect condition. I truly believe the Raptor R3X Grinding Wheel Bushing 2 Piece Set is the answer...yes you spend more money to get a great bushing, but it is well worth not having to deal with so many issues on any grinding wheel you might buy that comes with plastic bushings.
Productos recomendados
Mex $921.73
Mex $ 488 .00 Mex $488.00
Mex $888.23
Mex $ 479 .00 Mex $479.00
Mex $841.83
Mex $ 387 .00 Mex $387.00