Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

PSI Woodworking LDC2MT - Portabrocas de 1/2' con soporte cónico #2 Morse

Envío gratis en pedidos superiores a Mex $600.00

Mex $755.04

Mex $ 415 .00 Mex $415.00

En stock

Acerca de este artículo

  • Convierte el col muerto #2MT de tu torno en un col vivo con un portabrocas de 1/2" montado
  • Se monta en el maletero con el cenador de cono Morse #2 incluido; gira con rodamientos de bolas.
  • Después de ser montado, el col se convierte de muerto en vivo y aceptará mandriles, tacos, espigas, o cualquier eje de hasta 1,27 cm de diámetro.
  • Ideal para un soporte adicional seguro de la pieza de trabajo desde el extremo del portachuelos; permite centrar y agarrar husillos o tacos en el extremo de la cola.
  • No se puede utilizar para taladrar.


Convierte tu torno #2MT de cola muerta en un portabrocas vivo con un portabrocas de 1/2" montado. Se monta en el tubo trasero con el cenador Morse #2 incluido. Gira con rodamientos de bolas. Después de ser montado, el costre se convierte de muerto a vivir y aceptará mandriles, tacos, garras o cualquier eje de hasta 1/2" de diámetro. Ideal para un montaje adicional seguro de la pieza de trabajo desde el extremo de la cola del maletero; permite centrar y agarrar husillos o tacos en el extremo del cofre. Para la capacidad de perforación, TM32 está disponible por separado.


DSL
Comentado en los Estados Unidos el 4 de septiembre de 2024
Awesome tool, very sturdy and holds center perfect . Couldn't be any happier with the product.
Tom
Comentado en los Estados Unidos el 22 de abril de 2022
The only live chuck I can find that accepts a 1/2" shank. Has a tiny bit of play but it does the job.
David Maxwell
Comentado en Canadá el 4 de noviembre de 2021
Solid! Superb smooth ball races; turns incredibly freely and smoothly, with no slack whatsoever. The drill chuck is a little rough to open and close, but has no visible runout with 6" long drill chucked in it, (so maintains absolute centring). Only deficit is that the MT-2 tapered stem is slightly too short to make contact with the automatic release in the tailstock, and the end is not tapped, (as is sometimes done), to accept a short bolt or stud to make it slightly longer. I turned a little metal bead, with a stub stem to fit into the hole in the end of the stem, and glued it in place. Works perfectly. Highly recommended, and excellent value for the money. And an excellent way to create a live centre to accept turnings with a centre hole about which to turn, (in my case, spinning wheel bobbins).
Lee Y.
Comentado en los Estados Unidos el 24 de julio de 2020
Well constructed 3 jaw drill chuck, that runs true on it’s live tailstock bearing race. Makes it a simple process to create and use my own steel mandrels, in any diameter I need for my woodturning tasks.
D
Comentado en Canadá el 18 de marzo de 2017
Certainly not a precision chuck. There is 10 thousands runout on mine. Probably fine for a wood lathe but not for a metal lathe. It appears most of the run out is in the chuck itself so I am hoping replacing the poor quality chuck with something better will make it useable for my purposes. Buy Chinese tooling and take a chance, you might be luckier than me.
Productos recomendados

Mex $644.18

Mex $ 334 .00 Mex $334.00

4.7
Elegir

Mex $499.98

Mex $ 244 .00 Mex $244.00

4.7
Elegir