No hay artículos en el carro
No hay artículos en el carroCRISTINA
Comentado en México el 31 de marzo de 2025
AJUSTO PERFECTO EN MI ABANICO DE TECHO QUE TENIA LUZ CALIDA Y ESTA EN LA COCINA, ESTA GENIAL PARA EL ABANICO DE TECHO
Beckie
Comentado en los Estados Unidos el 2 de marzo de 2025
Easy to assemble and works great.
Duncan Finch
Comentado en Canadá el 6 de febrero de 2025
Bulb thus far works as expected after two weeks.I used this to replace a pre-existing LED in a ceiling fan and while the supplied mounts and hardware did not align with the old mounts, the bulb itself fit quote nicely into the old hardware. I did have to hardwire it in this application however as the connector supplied did not fit in the space I had. That being said I understand it's a generic item and can't fit every application perfectly. No complaints.
Customer
Comentado en los Estados Unidos el 3 de febrero de 2025
These are great but I had to modify the fit. Requires technical experience unless it's an exact fit.
luis Gerardo Mejia
Comentado en México el 17 de agosto de 2024
Excelente y facil de instalar
Charlie
Comentado en Canadá el 7 de julio de 2024
Got this for my Hampton Bay 52” ceiling fan and it worked like a charm to replace the existing round fluorescent bulb and transformer. Cut the plug from transformer and pigtailed it to the new light then it was plug and magnetize on the bottom of the light. Perfect fit.
HORTENSIA AVALOS SALAZAR
Comentado en México el 28 de junio de 2024
Bien. Muy buena iluminación. Fácil de instalar
Gerardo Gutiérrez Olavarrieta
Comentado en México el 19 de marzo de 2024
El unico inconveniente es que no trae el conector, hay que cortarlo del foco que quitas y ponerselo a este, pero es sumsmente sencillo, y funciona muy bien...
Jesus Gerardo Olua
Comentado en México el 5 de noviembre de 2024
Buena iluminación, buenos materiales.
manuel
Comentado en México el 22 de enero de 2024
Exacto lo que dice la descripción.
kbuck
Comentado en los Estados Unidos el 21 de enero de 2024
I used this module to replace the LED in a Minka-Aire Dyno ceiling fan. The "official" replacement module for these fans is expensive and hard to source, so I was motivated to find something better. Fortunately this module was great. To replace the fan's module, I had to take the old light assembly out and fully disassemble it. It was tricky to get the plastic off; I ended up needing to cut a notch in the edge of the plastic cover and then heat up the plastic with a hair dryer, which barely allowed me to jam a screwdriver in and work my way up to a putty knife, which finally popped the old LED module out. I disassembled both modules, swapped just the circuit boards, and cut the leads off of the old module. I used the wire nuts included with this module to attach the old module's wires to the input wires on this module and reassembled the whole thing. It works great.The only issue I ran into, which is entirely my own fault, was that the capacitors on this module are slightly too tall to fit inside the plastic housing of the Dyno ceiling fan LED module. This module is very thin so there's not much space at all. However, it was so close to fitting that you can't really tell that the plastic cap isn't fully seated, so it's visually fine anyway.This new module is brighter, more efficient, and has better CRI than the original, so I'm very happy with it.
Productos recomendados
Mex $479.99
Mex $ 259 .00 Mex $259.00
Mex $3,693.94
Mex $ 1,810 .00 Mex $1,810.00
Mex $259.00
Mex $ 139 .00 Mex $139.00