A pesar de que el servidor está arriba y puedo acceder desde el navegador, el 90% de las veces no imprime lo que hay en la cola de impresión, y tengo que reiniciarlo una y otra vez. Esto desde Windows, desde Mac ni siquiera imprime los trabajos enviados. Cabe destacar que el servidor lo tengo conectado por cable, ni siquiera por WiFi.

Debe ser bueno pero a mí no me sirvió para las impresoras

No puedo contactar al proveedor para un cambio o reemplazo del producto dañado, aun estando en garantía el producto, con el fabricante

Configure el Print Server para compartir una Samsung M2022W en una red local, debo decir que el wizard que trae no ayudo en nada.. termine hablando a Soporte Técnico quien amablemente me apoyo para resolver el problema de configuración que nada tiene que ver con el manual que viene en la caja.

Es muy difícil de configurar si no estás familiarizados con seteo de redes. Yo lo estoy y aún así me costó un par de intentos. Parece funcionar muy bien, sólo es un poco lento.

Ok, so I really wanted this product to work, I moved my PC to my family room and wanted to still be able to print to my Brother 2240D lazer printer.Got the product today, I can see that this was used previously (power supply cord was loose (no wire wrap around it), the CD Rom plastic tape was disturbed (can plainly see it), but I decided to give it a shot.Pitfall #1"The default IP for the device is 192.168.0.10When I cabled it to my PC, I was not able to access it through the web browser till.Had to change my Eithernet TCP/IP4 setting from auto detect to a static address of:192.168.1.50 (50 could be any number except 10)Subnet of: 255.255.255.0Once that was done All I had to do was follow these directions:https://sgcdn.startech.com/005329/media/sets/pm1115uw-setup-guide/pm1115uw%20setup%20guide.pdfI used the "Manual" method as the software on the CD did not load the setup wizard! Just as well.You might need help from your IP provider as to the SSID (name of the 2.4G signal), this server only operates on the 2. G frequency. But you might already have that if you are using your laptop/desktop or iPad over wireless, you can look and see what you are able to use, typically you can choose between 2.4 or 5G and each has a name (that's the SSID)So, what needs to be done once you get access to the server box is that you need change the IP address to what you network is. Example, my network is 192.168.1.1, the box default is 192.168.0.10, notice the second digit from the right side, 1 and 0 respectively, they don't match but they have to!So you have to change the server box to 192.168.1.xx (xx can be something like 60, which is what I used),the subnet is still 255.255.255.0Save/Rest and move on to the rest of the setup, although you may need to contact you IP support to get"Caution: once its reset to the new IP, you will need to go back into your Ethernet settings for TCP/IP4 and change that to 192.168.1.50 (notice the 1)Default Router number (this I absolutely needed to get from my IP)Authentication typeYou should already have the Password for your wireless network (that's the Security Key)Its not plug and play but its also not too complicated but you kind of need to be a bit of a "NERD" to get this done.The startech.com has a support and contact page, I remote chatted with a nice fellow that gave me the basics but I'm have no doubt that they will walk you through it.Its working well so far and hopefully will continue to do so for a long time.I learned a lot myself and if I ever change IPs, I will know what needs to be done to accommodate the print server.Its disappointing that I was not able to connect to the server box instantly after hooking up a cable to my PC, my PC should have automatically detected the IP address of the box and connected to it but I'm not a Network expert so I don't know where the fault lies for that (PC or the server box firmware) it was set to auto detect by default.But all is well, took about an hour to get it going.Bottom line, don't be afraid, the Server does work, requires a bit of knowledge but as long as you have access to your IP support and you do have chat to Startech (and phone number as well) you should be able to work through it!It was set to auto detect by default

Me funcionó perfecto para una impresora Zebra D420 para etiquetas

adapte mi impresora usb a ethernet y funciona a la perfeccion

funciona muy bien se pueden hacer cosas avanzadas con la aplicación de actualización de firmware

Setup is easy do not use the software provided and the instructions tell you nothing. Your router must have a WPS button or a WPS setup wizard (Wi-Fi Protected Setup). Enable the router WPS first then push and hold in the same button on the printserver for about 2 seconds. The 2 devices will find each other. Through your web browser check what the printserver IP address is on the router home page then use that address to get to the printserver setup page. Make the printserver address static not DHCP. To setup the printer just use windows to add the printer as a network printer with the correct model number and IP address. Reserve the printserver address so the router doesn't change it.

en lo básico hace lo que tiene que hacer, imprimir en una impresora USB por medio de la LAN.Pero quiero hacer notar que en impresoras multifunción, la info que envia la impresora a la PC no llega en muchos modelos modenros y no tan modernos, ejemplo una impresora L200 de EPSON, no se puede ver el nivel de la tinta y ni esperanzas de usar el escaner de la misma.Si tu impresora es básica, es un buen server de impresión, pero si tu impresora tiene mas funciones, mejor busca otra opción mas avanzada.Usé los drivers suministrados en el producto pero los resultados fueron los mismos. Sin embargo en una impresora laser HP básica trabaja muy bien!

No funciona en OSX El Capitan, de hecho el ordenador dejó de arrancar despues de instalar el controlador. No lo recomiendo para nada, lo devolví al dia siguiente.

De titel zegt genoeg, meer woorden moeten hier niet aan vuil gemaakt worden