No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Especificación:
Material: aleación de zinc
Peso: aproximadamente 682 g/24,1 oz
Velocidad del producto: 25000 rpm
Entrada de aire: 1/4
Tamaño del portabrocas: 3/8
Consumo de aire: 0,2 m³/min
Presión de uso de aire: 90 PSI
Aplicación: decoración del hogar, carpintería, torneado de agujeros , etc.
Lista de paquetes: 1 x taladro neumático; 1 conexión de aire; 1 llave inglesa; 1 manual de instrucciones.
Biggs
Comentado en los Estados Unidos el 21 de marzo de 2023
Photo clearly shows my 3/8 inch chuck on right. How do they get away with this
Jon Oliveira
Comentado en los Estados Unidos el 20 de diciembre de 2022
The drill works great just wish had different color
josh
Comentado en los Estados Unidos el 21 de noviembre de 2022
This drill is good and powerful. Bout it to drill our exhaust manifold bolts that broke but it spins way to fast. But I used it on other jobs and it did good just have to use a lot of oil do you don't burn your drill bits up
Family of 5
Comentado en los Estados Unidos el 20 de noviembre de 2022
Tool is smaller than i expected. Solid construction and easy to use trigger with safety switch. The end that you put any bit into is very close to the trigger and at times feels unsafe (this coming from working in a factory with similar tools) Works as intended, but I dont see myself using it too much due to the head being as close to the trigger as it is.
Val Anne Welch
Comentado en los Estados Unidos el 15 de noviembre de 2022
I purchased this, primarily, for its right-angle drilling capability. I wanted a tool I could get into tight spaces where I couldn’t get my electric drill, even with a right-angle attachment. Unfortunately, this isn’t that tool. The size is fine but the lack of torque makes it fairly useless for all but extremely light tasks. While testing I was able to put a new 3/16” bit through 1/2” plywood, but a 1/4” bit quickly bogged down and became stuck about 1” into a fir 2” X 4”. Since it isn’t reversible, had it been in a tight location, It could have been problematic to remove.So, what might it be good for? It’s a single-speed unit. The listing says 16,000 rpm. The included parts list claims 25,000 rpm. I have no way to measure this. Either way, you likely won’t be drilling metal. It might work in a situation where you are drilling small holes in softwoods or doing light deburring, polishing, or grinding, Just don’t bear down too hard. I was able to easily stop it with just my thumb and index finger when at full speed ( Don’t try this at home, I was wearing gloves, Your results may vary ) On any of those tasks I would more likely turn to a variable speed electric rotary tool. This unit is noisy and, since it is powered by a rotor with vanes, needs a fair amount of airflow to operate. My compressor has a 5-gallon capacity and cycled after almost every use.In conclusion:Pros:Relatively small and lightweightAppears to be solidly constructedDecent ergonomics, I liked the safety lock designHigh speed.Relatively low cost compared to similar productsCons:Very low torque. Lacks the power for anything beyond light tasksSingle speed, not reversibleNoisyRequires a large capacity compressor for frequent or semi continuous use ( unless you enjoy listening to it cycle )Included chuck key doesn’t fit well, too loose
Productos recomendados
Mex $6,545.38
Mex $ 1,881 .00 Mex $1,881.00
Mex $173.00
Mex $ 98 .00 Mex $98.00
Mex $2,921.94
Mex $ 1,344 .00 Mex $1,344.00