No hay artículos en el carro
No hay artículos en el carro Descripción del producto:
El kit de placa de expansión UCTRONICS GPIO T es un kit esencial diseñado para utilizar los pines GPIO de la placa base Raspberry Pi para conectar el panel LCD de 3,5 pulgadas y otros componentes al mismo tiempo.
Es compatible con Raspberry Pi 3 2 Modelo B B+ A+ A, cero W y Raspberry pi cero. Nos ayuda a conectar todas las versiones de frambuesa de la placa a varios sensores y componentes electrónicos y hace que el experimento sea más conveniente.
Características:
Tablero de pan de alta calidad.
La tabla de expansión tipo T y la tabla de pan hacen que el experimento sea más cómodo
Resuelve el problema de que no podemos usar GPIO.
100% compatible con Raspberry Pi
El paquete incluye:
1 tablero de expansión tipo T.
1 placa de pan de 830 puntos.
1 cable arcoíris de 40 pines hembra a macho a hembra.
65 cables de puente para tablero de pan
1 manual de usuario en inglés.
Nota: la placa Raspberry Pi y la visualización no están incluidos.
Bill
Comentado en los Estados Unidos el 26 de febrero de 2024
excellent tool for raspberry PI projects.
D. Doll
Comentado en los Estados Unidos el 18 de octubre de 2022
I needed a second breadboard and this came with a few other extras that came in handy. All items are high quality and work well.
Erik
Comentado en los Estados Unidos el 20 de abril de 2022
This review is for UCTRONICS Male to Female GPIO Ribbon Cable 40pin. There isn't a lot to say about this cable, and that is actually a good thing. Everything was done right on the cable that I received. It has the correct pin connections on both connectors to extend a Raspberry Pi GPIO hat outside the case. The strain relief on the cables is decent and the plastic connectors are good. Really, there is no reason to have a color coded cable, but it does let you verify that the cable is wired correctly. It is kind of nice to look at instead of another dull grey ribbon cable. I'm using this cable with a GPIO breakout board HAT that has LEDs, so it was very easy to tell that the cable was wired correctly. The length is enough to get outside the case without a lot of extra to flop around or introduce noise on the signals. I won't put the top on my case, but this cable will fit nicely through a small slot that is open on at least one side. The connectors obviously won't fit through a slot the size of the ribbon cable unless it is at a seam between the top and bottom.
DiVo
Comentado en los Estados Unidos el 22 de junio de 2021
This GPIO ribbon works as you would expect. I will say is durable, as I had to modify it to work with my raspberry pi touchscreen by cutting the plastic shroud to fit. The plastic put up a decent fight. Everything fit as intended and the pins were stiff, as they should be.
Phineas J Whoopee
Comentado en los Estados Unidos el 7 de noviembre de 2019
First the minuses.(-) Multicolor cable is pointless and serves zero purpose other than to increase cost.(-) Breadboard is segmented and has two groups of power rails. The ad shows this but I missed it. This means if you want the power rails to be contiguous, you have to jumper them. More of an inconvenience than anything else but it does cost you 8 pin positions. (see my attached photo where I added red and black jumper wires )Pluses(+) Breakout board is narrower than most GPIO Breakouts and therefore gives access to three rows of pins on each side.(Blue board in my pics) Competitors products such as the Kuman board(Red board in my pics) are too wide and sacrifice a row of pin access by blocking two rows.(+) Board has separate power pins which plug directly into the power rails. This is a HUGE benefit because it eliminates the need to run power jumpers directly off the already crowded GPIO power and ground and makes wiring much simpler.(+) The board has an LED power light "H U G E!!!!" advantage because it gives you that extra confidence that you have the ribbon cable plugged in correctly and that you have power going to the breadboard rails. This alone is worth buying this product. I can't tell you how many times when I am swapping out breadboards I inadvertently plug in the ribbon cable backwards. This fixes that.Note: Most breakout board use the Kuman(Red board in my photo) method and make the board too wide and require you to sacrifice a row of pins. There are other's that have the power pins like this board but I don't think they have the LED power indicator light.There's only one thing I wish they had which only one manufacture I've seen ever produced. That would be the ability to jumper select whether or not the power pins are 3Vdc vs 5Vdc. Unfortunately the maker of that product was in England and went out of business.
Productos recomendados
Mex $5,643.00
Mex $ 1,881 .00 Mex $1,881.00
Mex $180.56
Mex $ 108 .00 Mex $108.00
Mex $999.99
Mex $ 459 .00 Mex $459.00
Mex $452.42
Mex $ 230 .00 Mex $230.00