No hay artículos en el carro
No hay artículos en el carroLa válvula de retención Viair de 1/4 pulgadas hembra a 1/4 pulgadas macho evita que la presión del aire de acumulación se escape de los tanques de aire.
Austin S.
Comentado en México el 1 de marzo de 2025
Se ve de buen material, aún no lo eh instalado
Jeremy England
Comentado en los Estados Unidos el 5 de febrero de 2025
Needed a solution to put some crowd mics up on some pipe and drape at church. These worked perfectly for that application. Well built. Would easily buy them again.
Jay
Comentado en los Estados Unidos el 17 de febrero de 2025
My vair compressor was blowing the fuse too often. Read online that it could be a check valve. This worked perfect. Though I'm not sure how long these would last as the one that went bad was also a viar check valve.
Tommy
Comentado en México el 25 de julio de 2024
Excelente para batería pdp “recomendado”
Seth
Comentado en los Estados Unidos el 26 de junio de 2024
This is like a two-for-one package with a strong, reliable clamp and a strong, reliable ball head that can be used together or separately. The clamp holds nice and strong and has 1/4 and 3/8 mounting points on multiple surfaces. If you don’t quite trust its hold, you can thread a couple of zip ties through some of the screw holes and it’s not going anywhere. The ball head is all metal and holds surprisingly strong against more weight than I expected. Can’t go wrong with either part.
Byron K. Guernsey
Comentado en los Estados Unidos el 29 de marzo de 2024
Someone recommended this for holding drum mics, and I gave it shot. Its pretty good. Solid construction and securely clamps to just about anything. Its much better than the plastic clamps designed only to attach to the drum hoops with spring loaded mechanisms. You may however still want to add a gooseneck extension to allow for easier microphone positioning on drums since by itself it may be tricky to get the mic where you want it.
Steven
Comentado en los Estados Unidos el 5 de septiembre de 2024
Was perfect for adding the lower rotor mic onto my mic stand. Between this being added below and a bracket above, all 3 mics are supported by a single stand. You can adjust the grip to be VERY tight. So far it seems to support the heavy weight of the mic it holds very well. Stiff and adjustable joint for modifying the mic orientation. This clamp = Less stands needed, less clutter, more recording!
Nathan
Comentado en Australia el 27 de julio de 2023
Good quality unit.
Paola
Comentado en México el 24 de marzo de 2023
Todo muy bien. Llegó a tiempo y en buen estado
Jay
Comentado en Canadá el 14 de octubre de 2022
Arrived on time. Works great . Would definitely order again if I need one.
Stephen B.
Comentado en los Estados Unidos el 13 de octubre de 2022
So I was having an issue with fuses blowing. It got to the point where my fuse would blow instantly after replacing. Did a little research and found out it’s because this check valve went bad. Replaced it with this one and it’s now been over a month and no more blown fuses. If you are blowing your fuse, remove your check valve and see if you can blow through it. One direction you should be able to, but the other you should not. If you can, then it’s bad and should be replaced. I’m pretty sure this valve is exactly what came with my compressors from the factory.
Joshevelle
Comentado en México el 3 de agosto de 2021
Excelente producto y con materiales de primera. Justo lo que necesitaba, y no lo tenían en ninguna tienda de todo para el aire. Gracias!
valentin rodriguez
Comentado en México el 6 de julio de 2021
Excelente válvula y muy buena marca ... Le sirvió a mi suspensión
yves robitaille
Comentado en Canadá el 15 de agosto de 2020
anti-retour
InventPeace
Comentado en los Estados Unidos el 6 de marzo de 2012
This valve looks good on the surface.. and if you blow thru both ends "before" installing, it operates seemingly ok.. BUT when you tighten up the valve to insure no air leaking around threads (even using pipe thread tape) "SOMETHING" goes wrong, and it does not seal (prevent back flow of air into compressor ), which causes very hard or no start which can damage your compressor motor..THE SOMETHING in IMHO may be that when you tighten the valve up it deforms the orifice inside and prevents the valve from seating properly... thus you have long tedious installation with bad result and could damage your compressor motor if you are not standing right there to turn it off. AMazon send me a duplicate replacement.. same problem.. I finally went to Grainger and bought a differnt brand.. works great.. VIAIR needs to address the problem.
Productos recomendados
Mex $2,919.92
Mex $ 1,343 .00 Mex $1,343.00
Mex $725.51
Mex $ 348 .00 Mex $348.00
VIAIR 13844 1/4' Npt(M) a 3/8' Airline 90 Grados Giratorio Codo de Ajuste (Dot Aprobado) (Pack de 4)
Mex $634.68
Mex $ 291 .00 Mex $291.00