No hay artículos en el carro
No hay artículos en el carro LITEONE STEMS, TU MEJOR OPCIÓN
Diámetro del tubo Stereer: 28,6 mm.
Diámetro del manubrio: 31,8 mm.
Longitud: 90 mm.
Peso: 260 g.
Grado: 0-60° ajustable
Características:
Diámetro central del manubrio: 31,8 mm.
Diámetro del tubo estereer: 28,6 mm.
Grado: ajustable de 0 a 60 grados.
Longitud: 90 mm.
Peso: 260 g.
Tamaño: 31,8 x 28,6 x 90 mm.
Estilo: tallo de alta intensidad.
Material: aleación de aluminio AL6061 T6.
El paquete incluye:
1 vástago de bicicleta.
Cómo medir el tamaño de tu tallo:
a. Comprueba el diámetro del tallo original, elige el mismo tamaño que el diámetro original.
b. Mide el diámetro exterior del manubrio con regla y línea.
DJ
Comentado en los Estados Unidos el 16 de enero de 2025
Used this to get the bars a little higher and closer to me on my Heybike brawn, worked great! Fits perfect. Can comment on quality yet as I haven’t ridden it yet, but looks to be good quality.
Sprin
Comentado en los Estados Unidos el 13 de agosto de 2023
Only have a dozen miles, so far. Has absolutely changed my riding position (for the better) & feels like it's stable. Wasn't exactly the same size as my old stem, which left space. A 1mm spacer fixed the problem.
FloridaMan
Comentado en los Estados Unidos el 29 de abril de 2023
I debated on 4 stars or 5. It's everything I needed. My reach on my bike had my elbows locked driving all vibrations directly to my shoulders and my lower back was stressed as well. This stem allowed me to get the bars where I needed them and I'm now riding more comfortably. The only negative is that the stem has a creek in the center pivot point. That's the place where it rotates for the adjustment angles. I'm in my 50s and have been wrenching on things since I was a kid. So here is my assessment. I was able to get 99% of the creeking out by what I would normally consider over tightening. I think with a little better matching process it could be improved. With that said, I'm not a pro, there is a ton of load being placed on the components, and I'm not using a torch wrench so I'm basing my opinion on feel. For the money and what the product provides, I give it a 5.
Brandon
Comentado en los Estados Unidos el 20 de junio de 2022
Very easy to install, took about 10 minutes because I was being super cautious to not lose the little washers on the handlebar attachment. This brought my bars up and rearward and I am happy with it. I have less strain on my back and my neck since I'm riding more upright. And the bars are still in front of the stem so I have no issues with range of motion of my knees when pedaling while cornering. I installed it today very easily, and unlike installation videos online, there's no need to remove the adjustment mechanism. It can be loosened and pivoted after install. In fact, I recommend leaving it at 0 degrees to make aligning the handlebars with the wheel easier. After those are tightened up then pivot the riser to your desired angle and snug. Lastly rotate your handlebars to account for the new angle change.Overall a great buy especially for the price. Snug everything up and it holds tight and secure.
Charles F. Martek
Comentado en los Estados Unidos el 5 de junio de 2020
I am subtracting one star due to the issue I had with mine. Upon first inspection I was impressed with the apparent quality and machining of the unit. After adjusting to the desired angle I wanted and tightning the locking screw I noticed there was still movement at the joint. I tried tightning the screw further but it would not tighten and the joint was still loose. The joints have teeth that mesh when when the screw is tightened to prevent movement but in my case the teeth were not fully meshing when the screw was tightened. After removing the screw completely and disassembling the joint I noticed the problem. There is a spring inside that pushes the joint ends apart when you loosen the screw to allow adjusting of the angle. The spring in mine was too long and was being fully compressed when tightening the screw, preventing the screw from being tightened further. I cut about 1/4" off the spring length with a pair of diagonal cutters and re-assembled the joint. Now the joint locks solid with no movement even with only moderate tightening of the screw. I noticed reading other reviews that other people apparently had this issue and broke the unit or stripped the screw trying to tighten the joint not realizing it was the spring inside the joint causing the problem. I hope this helps other people if they run into this issue.After installing this on my bike I really like it and adjusting the handlebars up to a better position, the bike is much more comfortable to ride.
Productos recomendados
Mex $417.90
Mex $ 225 .00 Mex $225.00
Mex $269.00
Mex $ 137 .00 Mex $137.00