No hay artículos en el carro
No hay artículos en el carroDescripción del producto
ZoeRax Cat6 Jack Keystone RJ45 sin herramientas
Cumple con las normas TIA / EIA 568B.2-1 e ISO / IEC 11801; a través del análisis de impedancia de pines de contacto, terminales y PCB, para obtener el mejor rendimiento de juego de impedancias; conectores chapados en oro para evitar la oxidación de la superficie, mejorar el rendimiento de contacto y garantizar la vida útil; utilizando materiales de policarbonato ignífugo de alta calidad, cumple con el nivel UL94V-0; soporte 56. RA/56 RA/5Métodos de terminación 8RB. Diseño sin herramientas, giro y bloqueo para una instalación fácil y estable
Diseño sin herramientas de 90 grados
Simplemente inserta los cables siguiendo la codificación de colores y presiona hacia abajo la cubierta transparente.
Pin industrial RJ45-8P8C
50 micras, 99% chapado en oro puro en barrera de níquel
Contactos de bronecio fosforado
Los contactos de bronce fosósofo mantienen una conductividad óptima entre dos cables
Cómo instalar
Endereza los pares como se muestra
Coloca los cables en el conector Keystone
Empuja los cables en el conector Keystone
Presiona hacia abajo la tapa
Maureen K.
Comentado en los Estados Unidos el 6 de febrero de 2025
they worked but could not get a good connection. went out and bought ends that you use a clamp tool with and connection was 9 times better ( i have cable 1 Gig speed, able to get 90 mbs download with Zoerax ends, when i changed out the ends i got 870 mbs) the ends and clamp tool do cost more than these.
Messiah Cooke
Comentado en los Estados Unidos el 8 de abril de 2025
They work but I'll just use regular ones in the future. I don't like that the untwisted wire has to be longer to have enough to connect. Even with 23awg wire I've had them not set properly on the half that require longer wire to connect. I'll just keep using standard ones punch down tools are cheap and I already have 2. Thought it would be more convenient but in reality it was actually slower and more of a hassle.
Larry T. Rouse
Comentado en los Estados Unidos el 7 de diciembre de 2024
I used these to relocate my ISP modem, and they worked perfectly.The temptation is to try to put all the pairs in the jack and close the cover to punch them down all at once. Don't do that.Make sure the pairs are all cut to the same length. The wires can be inserted into holes at the top of the jack. Just insert the end of the wire into the hole at the top and bend it back into its slot. Insert the first wire and close the cover on it. Open the cover and insert the second wire, then close the cover on that one. Repeat that until you have all the wires punched down. Depending on the plenum-rated cable you are using, it might be impossible to close the cover to punch down all four pairs at once, but one at a time is no issue. I just used the wall plates I had on hand, which were from two different manufacturers, and these jacks snapped into them with no trouble.These are a little more expensive than the standard jacks that you can buy in bulk, so I might not use them for a big job, but they're perfect for adding one or two drops in a hurry. I'll keep a few in my tool bag.
Katie
Comentado en Canadá el 25 de enero de 2024
Sturdy enough for the price and easy to use. The back is fairly wide, so these aren't suitable if your panel or plate has very tight spacing.
Joel M Hinkle
Comentado en los Estados Unidos el 19 de enero de 2024
These do the correct crossing over internally so you just line up the colors per the code on the clip. I've had some where you do the rearranging of the wires before sticking them in and those suck. These were perfect, arrived fast and worked the first time.
Productos recomendados
Mex $1,175.00
Mex $ 493 .00 Mex $493.00
Mex $126.00
Mex $ 73 .00 Mex $73.00
Mex $149.00
Mex $ 80 .00 Mex $80.00