No hay artículos en el carro
No hay artículos en el carro Especificaciones:
Tipo: conector de bloque de terminales.
Tono: 5 mm.
Polos: 2P, 3P.
Tensión nominal: 300 V.
Corriente nominal: 16 A.
Rango de alambre: 22-14 AWG.
Resistencia de contacto: 20 mOhm.
Resistencia de aislamiento: 5000 MOhm/1000 V.
Voltaje de resistencia: CA 1500 V/1 min.
Temperatura Rango: -30 grados centígrados a+120 grados centígrados.
El bloque de terminales es un módulo importante en la industria eléctrica. Es conveniente conectar cables.
El paquete incluye:
30 conectores de bloque de terminales de 2 pines.
20 conectores de bloque de terminales de 3 pines.
Total: 50 unidades.
Nota: las condiciones de luz y las diferentes pantallas pueden causar que el color del artículo en la imagen sea un poco diferente del artículo real. El error de medición permitido es de +/- 1-3 cm.
CARL C.
Comentado en los Estados Unidos el 25 de agosto de 2024
Good item
Gabe5101
Comentado en los Estados Unidos el 7 de noviembre de 2024
Great Quality - Works as needed.
Ken Simmons
Comentado en los Estados Unidos el 7 de septiembre de 2023
No issues - they PERFECTLY FIT the 0.1" pitch Project Boards I have (with tinned, copper pads on BOTH SIDES). The fit is "just" snug enough in the board holes to hold the terminals while you solder ONE PIN to "lock it down" before soldering the rest of the pins.The screws are on the "small" size, requiring a "0" size Phillips to properly tighten/loosen them.The terminal holes themselves aren't "high quality", but if you ensure the wire end is in a FERRULE (up to #16 size, I think?) or TINNED or CRIMPED/SOLDERED to a connector pin, tightening the screw makes a Very Secure Connection.A BIG PLUS: the terminals can be "joined" to make LONGER terminal "chains". Just make sure your board is Long Enough to handle the chain. :)Finally, the PIN SPACING between terminals is ** 0.200" ** (i.e., TWO (2) HOLES), so ensure you factor that "real estate" need when you design your board layouts.For the "average" DIY-er, these are great. I WOULD NOT recommend them for "Mission-Critical" or similar "production" uses - $pend the $$$ on Higher-Quality terminals designed for "Mission-Critical, etc." needs.Otherwise, I ** DO RECOMMEND ** these terminals, with the noted "caveats, etc." above... :)
xyz
Comentado en los Estados Unidos el 13 de abril de 2023
These are good parts, except that its pins do not fit in the holes in the prototype board I have. They do fit well in a breadboard, but they are of little use unless I can enlarge the holes in my board. The spacing of the pins takes two "columns" on a board, but the terminals are large enough to be useful.
Rishi R.
Comentado en los Estados Unidos el 29 de junio de 2021
Liked that they fit snugly onto a solderless breadboard. Like that they align next to each other without jamming.Don’t like that the pins are spaced every two slots in the board so takes up unused space.
Productos recomendados
Mex $314.43
Mex $ 169 .00 Mex $169.00
Mex $4,330.47
Mex $ 1,732 .00 Mex $1,732.00
Mex $88.00
Mex $ 46 .00 Mex $46.00
Mex $1,488.99
Mex $ 714 .00 Mex $714.00
Mex $521.76
Mex $ 266 .00 Mex $266.00