No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Especificaciones:
Material: material de latón niquelado
Color: plata
Grado del interruptor: 3A 12V
Clasificación IP: IP65, IK08
Forma del botón: redondo
Ancho del hilo de rosca: 19 mm / 0.75 "
Dimensión: 2.1 x 2.6 cm / 0.83 "x 1.02"
Tipo de operación: Tipo momentáneo (empujarlo, liberarlo)
Paquete incluido:
1 x interruptor de botón
Nota:
1. Permita un error de 1-3 mm debido a la medición manual. Gracias por su comprensión.
2. Los monitores no están calibrados del mismo modo, el color del elemento que se muestra en las fotos puede mostrar un poco diferente del objeto real. Por favor tome el real como estándar.
César Donato Marrinez
Comentado en México el 9 de enero de 2025
Muy buena calidad recomendable 100%
Dan McKee
Comentado en los Estados Unidos el 8 de julio de 2023
As requested, shipped promptly. Looks good.
Baruj Covarrubias L.
Comentado en México el 10 de diciembre de 2023
El pulsador hace buen contacto, el cromo se ve bien. Solo que está algo grande, tal vez un poco más pequeño estaría mejor.
Joshua Klenke
Comentado en los Estados Unidos el 2 de julio de 2022
I used this as a killswitch in my favorite guitar mod project. Its got some absolutely killer ergonomics, and just enough click to be super satisfying without making stutters hard. A 3/4 inch drill bit turns a control knob hole on a stratocaster pickguard (or I imagine anything else) into a perfect fit for this absolute bargain of a top shelf part
Richard Gauvin
Comentado en Canadá el 14 de noviembre de 2022
Pour système de nitro moto
Lancelot Williams
Comentado en Canadá el 21 de diciembre de 2021
The switch is exactly as pictured on the product page, and has screw terminals for wire connection. As soon as it arrived I tested it to make sure it worked, and was pleased to find that the button has a clicky tactile feel to it which I associate with robustness. It measured between 0.4 and 0.5 ohms (my DMM can't go beyond the first decimal and kept wavering between the two) when pressed, so the contacts aren't perfect, but it's to replace the defective hatch release button on an old KIA Rio5 which can't take a proper repair and costs over $90 on this site to replace with one which will suffer the same fate. This switch won't have the same issue as the thin rubber membrane covering the plastic actuator on a 0.25-inch microswitch as supplied by KIA from the factory.Update Apr 2022: Switch still working perfectly fine, the 20AWG wiring I had installed failed so I replaced the wiring with tinned 14AWG multi-strand. Just letting everyone know that the wire through-holes on the terminals fit tinned 14AWG snugly. Also, since first buying the switch nearly five months ago, I've discovered that my DMM measures 0.3-0.4 ohms between just the probes, so this switch has negligible resistance. If I could, I'd give it six stars; honestly the worst thing about it is the tiny setscrews (use a #1 Philips bit for the best bite, it will cam out before causing any damage) and trying to access them with the switch inside the back hatch of a KIA through a hole which barely fits a Craftsman CMHT68008.
Omaha Paranormal
Comentado en los Estados Unidos el 14 de junio de 2019
Works perfect! Put it in my sons’ 1973 Super Beetle as a horn button.
Productos recomendados
Mex $201.00
Mex $ 112 .00 Mex $112.00