No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Joshua M. Hinman
Comentado en los Estados Unidos el 13 de marzo de 2025
The pre-soldered gpio pins allow for rapid integration into your projects.
K. D. Scott
Comentado en los Estados Unidos el 23 de febrero de 2025
This raspberry pi zero 2 w works perfectly. I was able to use the raspberry pi imager to flash raspberry pi os lite (64 bit) to it and it has been running ever since. The set up process was easy and it had no problems connecting to a router using the credentials specified during set up. I was even able to set up ssh keys on setup which allowed for an ssh connection immediately after it booted up. This pi zero 2 w has been running constantly since the evening it arrived, and I have noticed no issues with power, wireless, or installing packages. The only downside I found with this model over a standard raspberry pi (other than power/speed) is the interface. The pi zero has one mini hdmi port and one micro usb port for input and video. Using ssh is almost a necessity for configuration or normal use. That being said, the ssh setup is simple in the official imager. If you are in need of a pi zero, this one is worth a try.
michaelcrossland
Comentado en los Estados Unidos el 14 de febrero de 2025
I really liked this when I did get it to run. My only real issues are not something this seller could change. My grips are one that it still uses USB A micro plugs for bothe the power and the USB ports. Be way better if it was USB C. The other thing I found is that they say it's got half a Gigabyte of very slow SDR v2 but when ever I did a top ot htop on the system the most it showed that system had was like 300 MB of RAM for me so you need a very stipped down OS or use it with something that is not going to need to swap due to the very limited and slow RAM that it does. But why I gave 3 starts is due to the fact that I did get it setup and running some 3D printing server software for one my printers and it worked okay for about 8 hours and even with a heatsink on the CPU and it showing only running in the upper 39C rang most the time I just stopped working mid print and when I went to find out what had gone on it had rolled over and died on me no light s when it's plunged in to power and even tried to power from a USB C power bank with a USB tester inline to tell the power bank to only give 5V at 3A and still nothing at all from it. So watch it you might get one that does like mine did and just up and die for no get reason at all. I really was hoping that it would work so I could print a holder for it to pair up with my smaller 3D Printer to take with me when I go out to show off what can be done but not to sure if I want to take a risk on 30 more bucks.
Customer
Comentado en los Estados Unidos el 20 de abril de 2025
I had a Jumbo Hotspot and I could run Pi-Star or WPSD, but… it had a Pi Zero board in it and it was painfully slow to set up or even navigate through the settings once it was loaded. I mean VERY VERY SLOW. I purchased this board a Pi 2WH and swapped out the Pi Zero board to this one. It is as simple as unscrewing the old board, trimming four long pins on the bottom board and plugging this board in. It really is easy. This board is lightning fast by comparison. It applies the setup settings much quicker and moving through tabs in the interface is instant. A GREAT upgrade!!
Rick Angelone
Comentado en los Estados Unidos el 4 de abril de 2025
It ain't no zero, just try it
Productos recomendados
Mex $126.10
Mex $ 71 .00 Mex $71.00
Mex $622.52
Mex $ 280 .00 Mex $280.00
Mex $3,328.00
Mex $ 1,664 .00 Mex $1,664.00
Mex $511.49
Mex $ 260 .00 Mex $260.00
Mex $347.67
Mex $ 191 .00 Mex $191.00