No hay artículos en el carro
No hay artículos en el carro
23 herramientas de extracción de rodamientos de tracción delantera FWD
Este kit de prensa de rodamientos de rueda está diseñado para reducir la posibilidad de daños al cubeta y los rodamientos.
Esta herramienta instaladora de rodamientos de rueda se puede utilizar para la extracción de rodamientos de rueda en vehículos de tracción delantera y también se puede utilizar para instalar grandes rodamientos industriales
Cantidad total: 23pcs
El paquete incluye:
12 bujes
4 mangas.
2 placas de manga
2 arandelas.
1 tornillo.
1 tuerca
Instalador de cubeta de 1 rueda
Ten en cuenta que todas las tallas son de medición manual, puede haber pequeñas desviaciones.
Eje de transmisión: 32 y 38 mm.
Buje: 2.2 pulgadas. 2.5 pulgadas. 2.6 pulgadas. 2.8 pulgadas. 2.8 pulgadas. 2.8 pulgadas. 2.9 pulgadas. 7,5 cm. 3.1 pulgadas. 3.25 pulgadas. 3.3 pulgadas. 3.5 pulgadas.
Tornillo deslizante: largo 7.5 pulgadas x diámetro 1.9 cm.
Placa de la manga: 3.2 pulgadas de diámetro exterior x 2 .7 pulgadas. Paso; 4 pulgadas de diámetro exterior x 3.21 pulgadas. Paso
Manga: 3 pulgadas de diámetro exterior x largo 2.5 pulgadas; 3.25 pulgadas de diámetro exterior x largo 2.5 pulgadas; 3.63 pulgadas de diámetro exterior x largo 2.5 pulgadas.
Lavadora: 1.51 pulgadas de diámetro exterior
Tuerca: 3 pulgadas de largo x 0.75 pulgadas de diámetro.
michel remy
Comentado en Francia el 19 de septiembre de 2024
bien sûr, il n'y a pas de notice, mais en prenant le temps de comprendre, c'est redoutablement efficace et pratique. je l'ai essayé sur un moyeu de remorque de bateau( roulements étanches) et ça s'est très bien passé, tant au démontage , qu'au remontage. ( prévoir des cliquets/clefs costauds)
ChrisB55
Comentado en el Reino Unido el 18 de febrero de 2023
I needed this to remove rear wheel bearings on a 1989 Porsche 944. There is a good selection of discs to fit the bearing size. There were no instructions but it is pretty self explanatory what you have to do. I read another review that suggested using a thrust bearing washer on screw end where you tighten - that made sense and I bought a couple of 10mm washers even though you only need one. I applied some heat beforehand and used the tool with an impact drill (a ratchet will work), and the bearings popped out. Will definitely use this again but the for the price, it was invaluable to get it done quickly and without any damage.
Rynes
Comentado en Alemania el 11 de noviembre de 2022
Bolzen zu groß! Die anderen Teile passt genau, muß kleine Bolzen Xtra kaufen dann wird schon funktionieren
Customer
Comentado en los Estados Unidos el 19 de agosto de 2019
Aloha,Let me start by stating that I almost never write a review for anything. I think that this might be the 4th, or 5th review that I have ever written.This item deserves a few words. I assumed that this kit was nothing more than a cheaply made bunch of junk that would most likely break upon the first use, but worth the cost if I could just get the job that I needed it for done. Well...what can I say, other than I guess that I'll never learn to stop assuming the worst about things that I've never seen.This kit is very well made, and I suspect that it will be working well for many many years. The assortment of tools that are included in this kit should make the changing of pressed in front wheel bearings a breeze on any vehicle. The description of the product and what's included really do not do it justice.The description, and the pictures of the kit in the ad had me very concerned that the tools that I needed were not included in this kit, and to me, it looked like a toy. Well... in this case a picture is not worth a thousand words.I'd say that the vehicle that I was needing the tool for probably has one of the larger pressed bearings that are used on today's vehicles, and the tools that are included in this kit handled the job with ease.One of the reasons that I decided on this kit was the ability for use of an impact gun, which some other kits in this price range say you can not use.How well does it work ? Well... I spent less than an hour changing the front wheel bearing on a 2000 Nissan Quest. There was no need for removing the bearing/steering knuckle from the vehicle, which saved the need of a front end alignment after the job was done. Yes, I changed the bearing right on the vehicle.What did I save?Well, lets see, the machine shop quoted 100 bucks just for removing and installing the bearing, there was no need of a front end alignment which saved another 100 bucks, and, there was no time, or fuel used taking the part to the machine shop, or the need for returning to the shop to pick up the finished part the next day. Also, there was no need for spending an additional hour or so removing and reinstalling the bearing/ knuckle.,Bottom line... If you need a good quality bearing replacement kit for not a lot of money, I highly recommend this kit. But watch it, there are many kits that look like this kit for about the same cost, but those kits may not be this same quality. Then again, some kits could be better quality, but I doubt that a kit could be better in quality at this price level.Just make sure that the description says that an impact gun can be used, and if so, the kit should be OK.Aloha.
Barry
Comentado en Australia el 20 de septiembre de 2019
Good quality and well priced
Productos recomendados
Mex $441.41
Mex $ 216 .00 Mex $216.00
Mex $579.97
Mex $ 260 .00 Mex $260.00
Mex $211.39
Mex $ 124 .00 Mex $124.00
Mex $420.00
Mex $ 226 .00 Mex $226.00
Mex $2,249.46
Mex $ 1,079 .00 Mex $1,079.00
Mex $735.67
Mex $ 331 .00 Mex $331.00